• <label id="9r4ts"><track id="9r4ts"></track></label>

        1. 全自動造型機廠家


          全國24小時咨詢熱線: 13926238353




          黏土砂砂處理線主要作用是回收利用造型線的舊砂,通過落砂—破碎—篩分的等步驟處理后混合搭配新砂,重新為造型線造型主機提供射砂用砂。正常運行生產中全自動水平造型線單主機需配備25噸的黏土砂砂處理生產線,即主機聯動不停機不下芯的情況下,以510mm x 610mm的砂箱尺寸造型機,每小時的黏土砂消耗量為8噸左右。

          The main function of the clay sand processing line is to recycle the old sand of the molding line, mix and match the new sand through the steps of sand falling, crushing and sieving, and provide sand for shooting for the molding machine of the molding line again. In normal operation, the automatic horizontal molding line needs to be equipped with a 25 ton clay sand processing production line for a single main machine, that is, when the main machine is linked without stopping or dropping the core, with a 510mm x 610mm sand box size molding machine, the clay sand consumption per hour is about 8 tons


          The single machine equipment of clay sand processing line mainly includes vibration sand remover at the end of molding line, advanced magnetic separation, sand return belt, crusher, roller screen, hexagonal screen, boiling cooling bed, pulse dust remover, bucket elevator, right angle screen, used sand silo, high-speed rotor sand mixer and stock bin, etc., so as to realize integration, standardization and automation of the whole line, improve sand mixing efficiency and save labor At the same time, the dirty, disordered and poor working environment of the foundry was improved, which met the requirements of environmental protection policies.


          如若工廠廠房空間高度或企業資金受限制,使用“擺地攤”的形式單以造型機代替手工造型,也可搭配簡易的砂處理線,但鑒于以往的現場使用情況來看,簡易砂處理線主要存在的問題在于無法處理舊砂長期反復利用中積累的粉塵,特別是以下覆膜砂泥芯較多的鑄件生產,需定期往舊砂中摻入新砂保證型砂的透氣性,并且在舊砂的混砂過程中人工對于水分以及原料的搭配不容易掌控,因此我們建議針對于鑄件要求較高,光潔度要求較高的應當配合標準的黏土砂砂處理線。(上圖為兩臺550mm X 650mm/460mm的全自動造型機使用設計的30噸黏土砂砂處理生產線

          If the space height of factory buildings or enterprise funds are limited, the form of "floor stand" can be used to replace the manual molding by molding machine alone, or it can be matched with simple sand treatment line. However, in view of the previous field use, the main problem of simple sand treatment line is that it can not deal with the dust accumulated in the long-term repeated use of used sand, especially the following casting with more coated sand cores In the production of parts, it is necessary to regularly add new sand into the old sand to ensure the permeability of molding sand, and in the process of sand mixing of old sand, it is not easy to control the matching of water and raw materials. Therefore, we suggest that the clay sand treatment line with high casting requirements and high finish requirements should be matched with the standard. (the above figure shows the 30 ton clay sand treatment production line designed by two 550mm x 650mm / 460mm automatic molding machines)


          鑄造造型機廠家 長按二維碼添加微信好友


        2. <label id="9r4ts"><track id="9r4ts"></track></label>